The Best Valid NS0-014 Dumps for Helping Passing NS0-014 Exam!
UPDATED Network Appliance NS0-014 Exam Questions & Answer
NEW QUESTION # 44
What does the ONTAP Mediator specifically manage in an IP MetroCluster configuration?
- A. Load balancing
- B. Data deduplication
- C. Cluster failover events
- D. Data synchronization
Answer: C
NEW QUESTION # 45
What is a key advantage of IP MetroCluster over Fibre Channel MetroCluster?
- A. Increased storage capacity
- B. Easier setup and longer distance replication
- C. Lower bandwidth requirements
- D. Higher performance
Answer: B
NEW QUESTION # 46
What are two benefits of performing a Non-Disruptive Upgrade (NDU) in a MetroCluster environment? (Select two)
- A. Immediate application of all new features
- B. Avoidance of service outages
- C. Higher system performance during the upgrade
- D. Reduced risk of data loss
Answer: B,D
NEW QUESTION # 47
What factors should be considered when planning for the deployment of MetroCluster FC configurations? (Select two)
- A. Support for Fibre Channel
- B. Availability of ATTO bridges
- C. IP connectivity
- D. Number of Ethernet ports
Answer: A,B
NEW QUESTION # 48
What is the recommended maximum latency for the round-trip between two MetroCluster sites?
- A. 15 ms
- B. 5 ms
- C. 10 ms
- D. 1 ms
Answer: C
NEW QUESTION # 49
During the planning phase, which components are required for a MetroCluster solution assessment? (Select three)
- A. ATTO Bridges
- B. PowerShell integration
- C. IP addresses for management
- D. FC Switches
Answer: A,C,D
NEW QUESTION # 50
What is the recommended minimum distance between MetroCluster sites to avoid potential issues with data replication latency?
- A. 100 km
- B. 50 km
- C. 200 km
- D. 10 km
Answer: B
NEW QUESTION # 51
What are two core components of a MetroCluster IP architecture? (Select two)
- A. Inter-Switch Links (ISLs)
- B. ATTO FibreBridge
- C. Fibre Channel switches
- D. SyncMirror
Answer: A,D
NEW QUESTION # 52
Which task is essential when expanding a MetroCluster system to support additional storage nodes?
- A. Add new storage shelves and validate SyncMirror configuration
- B. Reinstall all controllers
- C. Remove ATTO FibreBridges
- D. Disable all replication processes
Answer: A
NEW QUESTION # 53
What is the role of Tiebreaker in MetroCluster configuration?
- A. Managing ATTO bridges
- B. Monitoring Fibre Channel health
- C. Ensuring IP compatibility
- D. Facilitating automatic switchover in case of WAN failure
Answer: D
NEW QUESTION # 54
What should you do before adding new nodes to an existing MetroCluster configuration?
- A. Run diagnostics on all existing nodes
- B. Verify that the new nodes are compatible using IMT
- C. Install a new mediator
- D. Disable SyncMirror
Answer: B
NEW QUESTION # 55
What are two benefits of transitioning from an FC-based MetroCluster to an IP-based MetroCluster? (Select two)
- A. Increased storage capacity
- B. Faster sync replication
- C. Easier long-distance replication
- D. Lower hardware costs due to fewer FC components
Answer: C,D
NEW QUESTION # 56
What is the primary purpose of the MetroCluster Tiebreaker in disaster recovery testing?
- A. To manage automatic failover between sites
- B. To perform data deduplication
- C. To automatically upgrade ONTAP
- D. To verify that storage shelves are properly synchronized
Answer: A
NEW QUESTION # 57
What technology does NetApp MetroCluster use to ensure zero data loss during failover?
- A. Snapshot
- B. Synchronous replication
- C. Deduplication
- D. Asynchronous replication
Answer: B
NEW QUESTION # 58
A customer is using MetroCluster Tiebreaker software with Observer mode set to true. Tiebreaker just confirmed a disaster at one site. Which two steps must you perform to recover the service?
(Choose two.)
- A. Execute the metrocluster switchover-forced-on-disaster true command on the surviving site.
- B. Execute the metrocluster configuration-settings -switchover true command on the disaster site.
- C. Open a case with the NetApp Support Site before executing any command on the system.
- D. Verify that the disaster site is down.
Answer: A,D
NEW QUESTION # 59
Which ONTAP service replicates cluster configuration between MetroCluster sites?
- A. vifmgr
- B. vldb
- C. mgmt
- D. crs
Answer: A
NEW QUESTION # 60
When troubleshooting a site failure in MetroCluster, which log file provides detailed information about the failure event?
- A. Cluster log
- B. ONTAP Syslog
- C. SyncMirror log
- D. Tiebreaker log
Answer: D
NEW QUESTION # 61
During the planning phase, which component is used to manage and monitor the MetroCluster environment?
- A. System CLI
- B. MetroCluster Manager
- C. Cloud Manager
- D. Active IQ Unified Manager
Answer: D
NEW QUESTION # 62
When planning MetroCluster, what is the recommended minimum WAN bandwidth for IP communication between two sites?
- A. 100 Mbps
- B. 1 Gbps
- C. 10 Mbps
- D. 10 Gbps
Answer: B
NEW QUESTION # 63
Which two tasks are performed by the MetroCluster Tiebreaker software? (Select two)
- A. Synchronizes data across nodes
- B. Manages site failover
- C. Configures SyncMirror
- D. Monitors cluster health
Answer: B,D
NEW QUESTION # 64
......
Updated NS0-014 Dumps Questions For Network Appliance Exam: https://www.validbraindumps.com/NS0-014-exam-prep.html
Latest Success Metrics For Actual NS0-014 Exam Realistic Dumps: https://drive.google.com/open?id=1WWujIYiaFbXvJMHRLwC_qHyIwJtyGCeu