2024 Updated NACE-CIP2-001 Tests Engine pdf - All Free Dumps Guaranteed!
Latest CIP Level 2 NACE-CIP2-001 Actual Free Exam Questions
To be eligible to take the NACE-CIP2-001 certification exam, candidates must have a minimum of two years of experience in the field of coating inspection at Level 1. They must also complete a NACE-approved training course in coating inspection before taking the exam. The training course covers the topics that will be tested on the exam and provides candidates with the knowledge and skills they need to pass the exam.
NEW QUESTION # 60
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Enforce the additional requirement
- B. Request clarification from the specifier
- C. Ignore the additional requirement
- D. Call your supervisor
Answer: A
NEW QUESTION # 61
Coating Surveys are legally required:
- A. On commercial marine vessels and offshore platforms
- B. On high pressure gas lines and fireproofed structures
- C. On food and beverage vessels and can linings
- D. On water tanks and potable water pipelines
Answer: A
NEW QUESTION # 62
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Flow stage
- C. Wetting stage
- D. Gel stage
Answer: B
NEW QUESTION # 63
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. powder coatings.
- B. epoxies.
- C. inorganic zincs.
- D. urethanes.
Answer: C
NEW QUESTION # 64
NACE No.13/ SSPC 6 identifies the use of:
- A. Steam cleaning only
- B. Abrasive blasting only
- C. Watterjetting only
- D. Various methods of cleaning
Answer: D
NEW QUESTION # 65
Which is used to calibrate a pH meter?
- A. Distilled water
- B. Deionized water
- C. Standard buffer solution
- D. Standard solvent solution
Answer: C
NEW QUESTION # 66
NACE Standards include:
- A. a) & b)
- B. Material Requirements
- C. a) only
- D. Standard Practices
Answer: A
NEW QUESTION # 67
Examples of non-ferrous metals include
Select All that Apply:
- A. copper
- B. mild steel.
- C. iron
- D. aluminum
Answer: A,D
NEW QUESTION # 68
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. Sacking
- B. Stoning
- C. Acid etching
- D. High-pressure water washing
Answer: A
NEW QUESTION # 69
When ASIN D 3363 is specified the Inspector must:
- A. Record the percentage of failure
- B. Record the highest value attained
- C. Use the correct solvent
- D. Record the two end points identified in the standard
Answer: D
NEW QUESTION # 70
Inspector reports should always be copied to:
- A. All parties involved in the project
- B. The Owner only
- C. Whomever the Owner identifies
- D. The Contractor and Owner
Answer: C
NEW QUESTION # 71
The primary purpose of Fireproofing coatings are to provide:
- A. fire extinguishing characteristics
- B. Preferential fuel for the fire
- C. Explosion resistance
- D. Temporary protection for the structure
Answer: D
NEW QUESTION # 72
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Coating Life Cycle Costs
- B. Lower Application Costs
- C. Lower Safety Enforcement Costs
- D. Lower Supervision Costs
Answer: A
NEW QUESTION # 73
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. True
- B. False
Answer: B
NEW QUESTION # 74
A reinforced coating is
- A. equally resistant to abrasion and impact as a non-reinforced coating.
- B. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. equally resistant to movement and impact as a non-reinforced coating.
- D. less resistant to movement, abrasion, and impact than a non-reinforced coating.
Answer: B
NEW QUESTION # 75
Inspection and Test plans are developed by referencing:
- A. The Specification, TDS, relevant Standards and Codes
- B. The Specification, SDS, relevant Standards and Codes
- C. The Specification, Application Guidelines, 'Relevant Standards and Codes
- D. The Specification, Safety Manual, Relevant Standards and Codes
Answer: A
NEW QUESTION # 76
NACE Level 2 Inspectors have been authorized to perform:
- A. All types of inspection without supervision
- B. Visual inspection, Non-Destructive and Destructive testing
- C. Visual inspection and Non-destructive testing
- D. Visual inspection only
Answer: B
NEW QUESTION # 77
NACE International Standards are developed by:
- A. International mandates
- B. Standard committees
- C. Government mandates
- D. Regional mandates
Answer: B
NEW QUESTION # 78
......
NACE-CIP2-001 certification exam is an internationally recognized certification for coating inspectors. NACE-CIP2-001 exam is administered by the National Association of Corrosion Engineers (NACE) and is designed to test the knowledge and skills of coating inspectors at Level 2. Coating Inspector Level 2 certification is widely recognized in the industry and is a prerequisite for many coating inspection jobs.
NACE-CIP2-001 Dumps Updated Practice Test and 100 unique questions: https://www.validbraindumps.com/NACE-CIP2-001-exam-prep.html
Latest 100% Exam Passing Ratio - NACE-CIP2-001 Dumps PDF: https://drive.google.com/open?id=1V7HKxZibUCkNaDS1WwABJne0N-kTsZCY