Ultimate Guide to Prepare HPE0-J58 Certification Exam for HPE Master ASE in 2021 [Q22-Q42]

Ultimate Guide to Prepare HPE0-J58 Certification Exam for HPE Master ASE in 2021

Use Real HPE0-J58 Dumps - HP Correct Answers updated on 2021

NEW QUESTION 22
Refer to the Exhibit.

A customer with an existing HPE Nimble installation sends you the output shown. The administrator who initially set up the replication has left the company.
They ask you what the current RPO level for their replication is. How should you respond?

A. They have an RPO of four minutes
B. They have an RPO of two minutes
C. They need to verify the RPO level from the host vc-ms-fileserver
D. They need to send a screenshot of the volumes tab

Answer: A

NEW QUESTION 23
Refer to the exhibit.

A customer has the environment shown. They currently perform application-consistent daily full backups via Veeam backup to an HPE StoreOnce device. These backups are then replicated to an alternate device using Catalyst copy.
Changing business requirements have mandated the RPO and RTO for the customer's SQL databases be reduced to 15 minutes. Due to the size of the databases, it is not possible to meet this requirement with their existing backout application.
What should you recommend the customer implement in order to meet their new requirement?

A. SPE StoreOnce Cloud Bank
B. HPE RMC Express Protect
C. HPE 3PAR Remote Copy in Synchronous Mode
D. HPE 3PAR Remote Copy in Asynchronous Streaming Mode

Answer: D

NEW QUESTION 24
Click and drag the steps on the left into the appropriate order on the right to set up an HPE 3PAR array in InfoSight.

Answer:

Explanation:

NEW QUESTION 25
Refer to the exhibit.

A customer is considering a new HPE 3PAR for the purpose of implementing deduplication and compression.
Based on the output returned from the NinjaCrawler tool, what do you know about the customer data?

A. This data has a block size which is not optimal for HPE 3PAR
B. This data has a video data workload profile
C. This data is from an HP-UX system
D. This data is a good candidate for HPE 3PAR deduplication

Answer: C

NEW QUESTION 26
A customer has a requirement to provide disaster recovery for an application. The application has an RPO of
30 mins, with an RTO of 15 mins. How can HPE 3PAR Remote Copy help meet the customer's specified requirements in the most cost effective manner?

A. by using Synchronous Replication
B. by using Synchronous Long Distance Mode
C. by using Streaming Asynchronous replication with an interval of 15 mins
D. by using Periodic Asynchronous Replication with an interval of 15 mins

Answer: A

Explanation:
Explanation

NEW QUESTION 27
You are starting an assessment to design a new multi-storage environment for a customer. You have collected data on all the current arrays using SAF collector.
What should be the next step in your design process?

A. Open the .zip file with NinjaSTARS
B. Send the .zip file to [email protected]
C. Import the .zip file into OCA
D. Upload the .zip file to the SAF Portal

Answer: A

NEW QUESTION 28
A customer is interested in using HPE InfoSight Cross-stack Analytics for VMware.
Where does the customer need to make the appropriate configuration changes to makes this active?

A. HPE 3PAR SSMC
B. VMware vCenter
C. HPE InfoSight Portal
D. HPE 3PAR Service Processor

Answer: C

NEW QUESTION 29
A customer experiences a performance issues and blames the HPE 3PAR array. However, you suspect it is caused by a noisy neighbor situation in the VMware environment. Which approach should you use to find and prove a root cause?

A. Use Brocade Network Advisor to gather data for analysis
B. Use the advanced performance reports in SSMC
C. Use HPE SAF Collect to gather data for SAF Analyze
D. Use HPE InfoSight Cross Stack Analytics

Answer: B

NEW QUESTION 30
A customer has standardized on Windows Server. They need to ensure that application and storage will move between sites as one during automated or manual failover. Which HPE 3PAR integrated solution should you recommend to the customer as a preventative measure?

A. Cluster Extension (CLX)
B. Serviceguard Metrocluster
C. Site Recovery Manager
D. Peer Persistence

Answer: A

Explanation:
Explanation/Reference: https://tdhpe.techdata.eu/Documents/TDAS-Integrated%20Systems/Technical%20White%
20Paper_HPE%20ConvergedSystem%20700.pdf?epslanguage=en

NEW QUESTION 31
A customer needs to upgrade their existing HPE 3PAR environment. They ask you to present a solution to gather data from all 200 of their HPE 3PARs arrays, which are spread across the globe. The arrays consist of various generations and OS levels, and they are managed by regional instances of SSMC. What should you present to the customer as a solution?

A. using the upgrade report tool in HPE InfoSight
B. using a script based on the HPE 3PAR Web Services API
C. using an HPE 3PAR CLI script with the checkupgrade command
D. using the SSMC array configuration reports

Answer: D

Explanation:
Explanation/Reference:
Reference: https://support.hpe.com/hpsc/doc/public/display?docId=c05243943

NEW QUESTION 32
You are discussing a HPE 3PAR Remote Copy solution with your customer. The customer has had a bad experience in their current non-HPE replication solution. Currently the source and target volume properties on the array must be identical on both sides and cannot be changed without re-creating the volumes.
What should you explain to the customer?

A. Flash data can only be replicated to flash media on the target array, while spinning media can be replicated to flash media
B. All data from the source array will automatically be replicated to the target array using AI to determine the best location where to store the data
C. Source and target disk type and RAID level can be different and adapted to changing requirements
D. On the target array volumes can be pinned into cache for maximum flexibility

Answer: A

NEW QUESTION 33
A customer has an HPE Nimble Storage array. They plan to add a second HPE Nimble Storage array to their existing group.
What is the expected write behavior to a volume once the new array is added to the same pool as the existing array?

A. Data will be written to the new array until it is the same percent full as the original array
B. Data will continue to write to the first array until there is 40% free space available, and then alternate writes between the two arrays
C. Data will immediately start to alternate writes between the two arrays
D. Data will be stripped and automatically re-balanced across the two arrays

Answer: A

NEW QUESTION 34
Refer to the exhibit, which reflects the Bill of Materials (BOM) configuration for one datacenter.

A customer needs a new storage solution of two HPE 3PAR 8440 arrays. The customer's environment consists of eight physical servers in each data center attached to the SAN and one StoreOnce 3540 system with two FC I/O cards. The distance between data centers is less than 75 meters.
What should you add the BOM to meet the customer needs?

A. one HPE 3PAR StoreServ 8000 Direct Connect Cabling Option for Drive Enclosure for each HPE
3PAR 8440
B. one HPE SN3000B SAN Switch 12-port Upgrade E-LTU per switch, appropriate number of SFPs and cables
C. one HPR 3PAR StoreServ AC RPS Service Processor
D. one HPE 25m Mini SAS High Density Active Optical Cable for each HPE 3PAR 8440

Answer: C

NEW QUESTION 35
You want to use FCAP authentication in an environment with FOS 7.3 running switches with no extra licenses.
What should you do to use this feature?

A. Certificates must be obtained from a third-party vendor
B. Certificates must be obtained from Brocade
C. A Secure Fabric license must be added to all switches in the fabric
D. Switches must be upgraded to FOS 7.4 or higher

Answer: D

NEW QUESTION 36
A customer needs a data recovery solution for their HPE 3PAR array. They have the following requirements:
* RPO needs to be within three hours
* RTO needs to be within three hours
* There is no need for offsite data archive
* They will have a limited maintenance window
Which solution meets all of the customer needs?

A. HPE StoreOnce
B. HPE StoreAll
C. HPE StoreEver
D. HPE 3PAR StoreServ with RMC

Answer: D

NEW QUESTION 37
A customer has an aging Fibre Channel SAN from one vendor and a separate iSCSI SAN from another vendor. The customer wants to upgrade to a single vendor that will allow them to manage the SAN through a single vendor management console.
Which solution should you recommend?

A. one HPE Nimble Fibre Channel group federated to an HPE 3PAR for iSCSI
B. one HPE Nimble iSCSI group federated to an HPE 3PAR for Fibre Channel
C. one HPE Nimble Storage Fibre Channel Group and one HPE Nimble Storage iSCSI Group
D. one HPE Nimble Storage Group that has a Fibre Channel port and a ISCSI pool

Answer: C

NEW QUESTION 38
An HPE Nimble customer needs to consolidate storage and scale performance. They are looking to purchase additional hardware to meet these requirements.
What is the best solution to offer this customer?

A. Add additional HBAs in the arrays
B. Use multiple single-array storage pools
C. Use multi-array storage pools
D. Add additional SSDs to the cache

Answer: B

NEW QUESTION 39
A customer wants an HPE 3PAR array with about 400,000 IOPS and over 6000 MBs per second through - put at 16K block size. What should you consider in your design?

A. Configure the HA-enclosure to protect against enclosure failure
B. Ensure that the write IO service time on the array is under 2ms
C. Focus the configuration on the effective capacity ratio rather than data reduction ratio
D. Adhere to the initiators per port, initiators per system, and fan-in/fan-out limits in SPOCK

Answer: C

NEW QUESTION 40
A customer wants to enable an automated failover for their two existing HPE 3PAR solutions, which are located in two different sites. Each solution has an All-inclusive Single-System Software license.
Which component is required to enable this function?

A. Additional HPE 3PAR system as quorum witness
B. Dark fibre connection between the sites
C. Fibre channel Bridges to connect the disk shelfs
D. All-inclusive Multi-System Software License

Answer: D

NEW QUESTION 41
A customer has a requirement to provide disaster recovery for an application. The application has an RPO of
30 mins, with an RTO of 15 mins. How can HPE 3PAR Remote Copy help meet the customer's specified requirements in the most cost effective manner?